Cisco CCNA 200-301 Practice Test

Cisco Practice Tests

Question 1 / 55 - Mode : Exam
If you take the network 192.168.1.0/24 and create four subnets from it, what are the new subnet IDs? (Choose four) A. 192.168.1.128 B. 192.168.1.32 C. 192.168.1.96 D. 192.168.1.64 E. 192.168.1.192 F. 192.168.1.0 You have the network 192.168.5.0/24 that has been subnetted to /30 networks. What is the subnet ID of the seventh subnet that was created? A. 192.168.5.28/30 B. 192.168.5.16/30 C. 192.168.5.12/30 D. 192.168.5.24/30 E. 192.168.5.32/30 F. 192.168.5.20/30 What is the name of the firewall feature that, when used, can maintain a historical database of each connection through a device: Where it was sourced, destined, and which protocol and protocol port it was using? A. Stateless Inspection B. Stateful Inspection C. Network Protocol Analysis D. Protocol State Analysis What will occur when you issue the “copy startup-config running-config“ command on your IOS device? A. The configuration in RAM will replace the configuration in NVRAM B. The configuration in NVRAM will merge with the configuration in RAM C. The configuration in FLASH will merge with the configuration in RAM D. The configuration in FLASH will replace the configuration in RAM E. The configuration in NVRAM will replace the configuration in RAM Using the exhibit as a reference, what is a valid key? A. ”lastUpdateTime”: 1572317520439 B. ”CSR1000V” C. ”role” D. ”platformId”: Which of the following describes the manual IP addressing mechanism when configuring a DHCP server? A. A network administrator assigns an IP address to a client B. A client is assigned an IP address for a limited amount of time C. A non-expiring IP address is assigned to a client https://www.learncisco.net/courses/icnd-1/lan-connections/router-as-a-dhcp-server.html Identify the fields in an IPv4 header. (Choose three) A. Host component B. Time to Live C. Source address D. Destination address E. Network address https://www.learncisco.net/courses/icnd-1/building-a-network/tcpip-internet-layer.html Which command is used to verify the interfaces that are participating in the RIPv2 routing process? A. show ip rip B. show ip protocols C. show ip route D. show rip interfaces E. show ip interface brief Your Cisco IOS router is acting as a DHCP server. Which command will display the addresses that have been handed out to clients on the LAN? A. show ip dhcp assignments B. show ip dhcp address C. show ip dhcp conflicts D. show ip dhcp bindings E. show ip dhcp pool You are troubleshooting the components involved in IPv6 end-to-end connectivity on a Mac computer. Please select the command you will use to check IPv6 static name resolution. A. show ipv6 interface B. show ipv6 route C. show ipv6 access-list D. ping E. ipconfig F. ifconfig https://www.learncisco.net/courses/icnd-2/troubleshooting-basic-connectivity/path-selection-dns-and-acl-issues-in-ipv6.html A Cisco Catalyst switch connects to what should be individual user PCs. Each port has the same port security configuration, configured as follows: interface range gigabitethernet 0/1 - 24 switchport mode access switchport port-security switchport port-security mac-address sticky Which of the following answers describe the result of the port security configuration created with these commands? (Choose two) A. Prevents unknown devices with unknown MAC addresses from sending data through the switch ports. B. If a user connects a switch to the cable, prevents multiple devices from sending data through the port. C. Will allow any one device to connect to each port, and will save that device’s MAC address into the startup-config D. Will allow any one device to connect to each port, but will not save that device’s MAC address into the startup-config What is used to determine the MAC address of a known IPv6 address? A. ARPv6 B. DHCP C. ARP D. DHCPv6 E. Router discovery F. Neighbor discovery Looking at the exhibit, what key:value pair option has a value that is numeric in nature? A. ”upTime”: ”45 days, 13:36:14.80”, B. ”lastUpdated”: ”2019-10-29 02:52:00”, C. ”managementIpAddress”: ”10.230.1.1”, D. ”lastUpdateTime”: 1572317520439 Which of the following protocols are used to auto negotiate trunk formation between two switches? A. CDP B. VTP C. DTP D. STP Which command displays information about security options configured on an interface? A. show port-security interface [interface-id] B. show port-security [interface-id] C. show port-security[address] D. show security [interface-id] You have HRSP configured on your network with R1 as the active default gateway and R2 as the standby default gateway. What is the best way to configure PC1 to ensure that it is using a redundant default gateway? A. Create a default route to R2, in case R1 goes down B. Ensure that the same priority is assigned to R1 and R2 C. Ensure that it is assigned the virtual default gateway D. Ensure that it is configured with two default gateways Some IOS commands store passwords as clear text, but you can then encrypt the passwords with the service password-encryption global command. By comparison, other commands store a computed hash of the password, rather than storing the password. Comparing the two options, which one answer is the most accurate about why one method is better than the other? A. Using hashes is preferred because encrypted IOS passwords can be easily decrypted. B. Using hashes is preferred because of the large CPU effort required for encryption. C. Using encryption is preferred because it provides stronger password protection. D. Using encryption is preferred because of the large CPU effort required for hashes. How are PDUs handled during the peer-communication process? (Choose two) A. The Internet layer encapsulates data and attaches a header to create a PDU known as a frame B. Header information within a PDU is required and can include information such as source and destination logical addressing C. The link layer provides a service to the network layer by encapsulating the network-layer packet into a PDU called a segment D. The application layer protocol begins the process by delivering PDUs to the transport layer https://www.learncisco.net/courses/icnd-1/building-a-network/tcpip-internet-layer.html Which of the following attributes do QoS tools manage? (Choose three) A. Bandwidth B. Delay C. Load D. MTU E. Loss Devices using a wireless LAN must operate in which one of the following modes? A. Round-robin access B. Half duplex C. Full duplex D. None of these answers Which shorthand notations can be applied to IPv6 addresses? (Choose three) A. An unspecified address is written as a double colon followed by four zeros B. Leading zeros in a field are optional C. Format is x:x:x:x:x:x:x:x, where x is a 16-bit hexadecimal field D. Successive fields of 0 are represented as "::" but only once in an address E. Hexadecimal digits A-F are case sensitive https://www.learncisco.net/courses/icnd-1/introducing-ipv6/ipv6-address-types.html What command should you configure globally to enable a 15-minute recovery time for the port security errdisable state? A. errdisable recovery interval 15 B. errdisable recovery timer 15 C. errdisable recovery timer 900 D. errdisable recovery interval 900 What is the function of the command switchport trunk native vlan 999 on a Cisco Catalyst switch? A. It creates a VLAN 999 interface. B. It designates VLAN 999 for untagged traffic. C. It blocks VLAN 999 traffic from passing on the trunk. D. It designates VLAN 999 as the default for all unknown tagged traffic. https://www.learncisco.net/courses/icnd-1/medium-size-switched-network-construction/vlans-and-trunk.html Which command can be used to verify that the current IPv6 path matches the desired route to the server? A. show ipv6 cef B. show ipv6 mroute C. show ipv6 neighbors D. show ipv6 route What network mask should be used with Class B network to create 40 subnets? A. 255.255.248.0 B. 255.255.255.0 C. 255.255.252.0 D. 255.255.192.0 E. 255.255.254.0 https://www.learncisco.net/courses/icnd-1/lan-connections/network-addressing-scheme.html Which of the following controllers (if any) from Cisco uses a mostly centralized control plane model? A. Cisco Open SDN Controller B. Cisco Application Policy Infrastructure Controller (APIC) C. Cisco APIC Enterprise Module (APIC-EM) D. None of these controllers uses a mostly centralized control plane. Wired Ethernet and Wi-Fi are based on which two IEEE standards, respectively? A. 802.1, 802.3 B. 802.1, 802.3 C. 802.3, 802.11 D. 802.11, 802.3 To connect a Cisco wireless LAN controller to a wired network, which of the following would you use? Assume that this connection will carry traffic to and from APs. A. Console port B. Service port C. Distribution system port D. AP data port What are three features of the IPv6 protocol? (Choose three) A. optional IPsec B. autoconfiguration C. no broadcasts D. complicated header E. plug-and-play F. checksums https://www.learncisco.net/courses/ccna/part-8-internet-protocol-version-6/addressing.html Four OSPF routers connect to the same LAN. In a new election after all routers have been rebooted, which router wins the DR election? A. R4, router-id 4.4.4.4, priority 1 B. R3, router-id 3.3.3.3, priority 2 C. R1, router-id 1.1.1.1, priority 4 D. R2, router-id 2.2.2.2, priority 3 Of the figures shown, which depicts an accurate Clos Architecture? A. Topology A B. Topology B C. Topology C D. Topology D By default, no password is required to connect to the console port. Which commands are required to enable local line authentication for the console port? (Choose two) A. enable B. exec-timeout C. privilege D. login E. secret F. password Which statements correctly describe how ACLs function? (Choose two) A. There is an implicit deny all at the bottom of each ACL B. There is immediate execution upon a match C. The last entries in an ACL are processed first D. ACLs can be used only for filtering https://www.learncisco.net/courses/icnd-1/acls-and-nat/understanding-acls.html What type of access-control list allows you to match traffic based on protocols and port numbers? A. Standard IPv4 numbered ACL B. MAC address ACL C. Standard IPv4 named ACL D. Extended IPv4 numbered ACL What option(s) are required criteria for a service to be a cloud service? (Choose two) A. Rapid elasticity B. Agile network access C. Measured service D. Proactive service An enterprise plans to start using a public cloud service, and is considering different WAN options. The answers list four options under consideration. Which options provide good security by keeping the data private while also providing good QoS services? (Choose two) A. Using private WAN connections directly to the cloud provider B. Using an Internet connection without VPN C. Using an intercloud exchange D. Using an Internet connection with VPN You have changed the domain name for one server in a VTP domain to Sales. What happens to other servers with a domain name of null in the same VTP domain area? A. They will have a domain name of Sales B. They will need to have their domain name manually set C. They will display an error D. They will retain a domain name of null What is the field that is used on modern systems that allows an IP packet to be marked with a specific QoS value? A. EXP B. CoS C. DSCP D. Traffic Class Which command is used to import a static default route into the RIP routing process and have it advertised to other neighboring RIP routers? A. default-information originate B. redistribute static C. ip route 0.0.0.0 0.0.0.0 next-hop_ip D. network 0.0.0.0 The Wi-Fi Alliance offers which of the following certifications for wireless devices that correctly implement security standards? A. WEP B. WPA2 C. 802.11 D. AES Which of the following components contains the operating system? A. Interface B. ROM C. Flash D. RAM E. CPU F. NVRAM https://www.learncisco.net/courses/icnd-2/network-management/router-internal-components-overview.html Which cloud service model gives a customer complete control over the virtual hardware components, including processor performance, network connectivity, how much memory and storage space is required, and potentially the operating system that is preinstalled? A. SaaS B. IaaS C. PaaS D. TaaS If you want to be alerted when a device configuration differs from the intended configuration, what should you implement? A. Version control B. Centralized configuration C. Configuration drift D. Configuration monitoring Which of the following behaviors is applied to a low latency queue in a Cisco router or switch? (Choose two) A. Congestion management B. Shaping C. Policing D. Priority scheduling E. Round robin scheduling Per the command output, with how many routers is router R9 full adjacent over its Gi0/0 interface? A. 7 B. 10 C. 5 D. 2 Which ports go into a blocking state in the final step of the spanning-tree algorithm? A. Root ports B. Designated ports C. Nonroot or nondesignated ports D. All available ports Where is the Cisco IOS stored on a Cisco IOS ISR Router? A. CPU B. Flash C. RAM D. NVRAM E. ROM Refer to the exhibit; in which area would R1’s Gi0/0 interface be placed? A. 5 B. 6 C. 10 D. 11 What source will be chosen when a destination network offers multiple sources? A. The dynamic route B. The route with the highest metric C. The source with the lowest administrative distance D. The static route https://www.learncisco.net/courses/icnd-1/lan-connections/functions-of-routing.html Which of the following QoS marking fields could remain with a packet while being sent through four different routers, over different LAN and WAN links? (Choose two) A. CoS B. IPP C. DSCP D. MPLS EXP What are the solutions to the public IPv4 addressing shortage? (Choose three) A. Subnetting B. ARP C. Use of private IPv4 addresses D. DHCP E. IPv6 F. Creating more public IPv4 addresses Which of the following describes the Port Address Translation configuration? A. Manually configured, one-to-one address mapping B. Automatically assigned from an address pool, many-to-many address mapping C. Many-to-one address mapping https://www.learncisco.net/courses/icnd-1/acls-and-nat/address-translation.html What is the function of PVST+? A. Multiple 802.1w per VLAN B. One 802.1D per VLAN C. One 802.1w per VLAN D. Multiple 802.1D per VLAN https://www.learncisco.net/courses/icnd-2/vlans-and-spanning-tree/pvst.html The IP component of TCP/IP determines where packets of data are routed based on their destination addresses. IP has certain characteristics that are related to how it manages this function. Identify the characteristics of the Internet Protocol. (Choose three) A. An Internet Protocol version 4, or IPv4, address contains 32 bits B. IP is a layer 3 media-independent connectionless protocol that uses hierarchical logical addressing and provides best-effort service C. IP works at the transport layer of the TCP/IP stack D. An IPv4 header address field contains a 32-bit binary value that represents the IP address of the sender E. An IPv4 header address field contains a 24-bit binary value that represents the IP address of the receiving endpoint https://www.learncisco.net/courses/icnd-1/lan-connections/network-addressing-scheme.html Given the output from a working OSPF router, as seen in the exhibit, how many neighboring routers exist? B. 1 C. 2 D. 3 E. More than 3

Our Recommended Premium CCNA Training Resources

These are the best CCNA training resources online:

Click Here to get the Cisco CCNA Gold Bootcamp, the most comprehensive and highest rated CCNA course online with a 4.8 star rating from over 30,000 public reviews. I recommend this as your primary study source to learn all the topics on the exam.

Want to take your practice tests to the next level? AlphaPrep’s purpose-built Cisco test engine has the largest question bank, adaptive questions, and advanced reporting which tells you exactly when you’re ready to pass the real exam. Click here for your free trial.

The CCNA 200-301 is for the Cisco Certified Network Associate (CCNA) Implementing and Administering Cisco Solutions exam. You can use the practice test to check your knowledge and improve your understanding in preparation for the Cisco CCNA certification exam.

The Cisco CCNA 200-301 practice exam tests include questions to test your knowledge and skills related to Cisco networking fundamentals, which helps you pass the actual exam.

The Cisco CCNA exam objectives include Cisco network fundamentals on routers, switches, IP addresses, etc., network access, IP connectivity such as static and dynamic routing protocol, IP services, network security fundamentals, and automation and programmability.

Cisco CCNA 200-301 Practice Test

Complete this form to get your score report

Our Recommended Premium CCNA Training Resources