Cisco CCNA 200-301 Practice Test

Cisco Practice Tests

Question 1 / 55 - Mode : Exam
Which of the following layer 2 WAN protocols is the most scalable transport technology ever developed? A. HDLC B. Ethernet C. Frame Relay D. ATM E. PPP https://www.learncisco.net/courses/icnd-2/wan-technologies/serial-encapsulation.html Which aspects can you check to verify that IPv6 is configured correctly? (Choose three) A. Interfaces have the IPv6 address configured B. Correct cable is being used C. IPv6 routing is enabled on the router D. Routing protocols that are configured for IPv6 E. IOS is up to date A Cisco Catalyst switch connects to what should be individual user PCs. Each port has the same port security configuration, configured as follows: interface range gigabitethernet 0/1 - 24 switchport mode access switchport port-security switchport port-security mac-address sticky Which of the following answers describe the result of the port security configuration created with these commands? (Choose two) A. Prevents unknown devices with unknown MAC addresses from sending data through the switch ports. B. If a user connects a switch to the cable, prevents multiple devices from sending data through the port. C. Will allow any one device to connect to each port, and will save that device’s MAC address into the startup-config D. Will allow any one device to connect to each port, but will not save that device’s MAC address into the startup-config Identify the purpose and functions of VLANs. (Choose three) A. Flexibility in grouping users together logically B. Access port security C. Protocol and port number provisioning D. Segmentation of network users E. Inbound or outbound interface VLAN configuration https://www.learncisco.net/courses/icnd-1/medium-size-switched-network-construction/vlans-and-trunk.html Suppose you would like to select a method to protect the privacy and integrity of wireless data. Which one of the following methods should you avoid because it has been deprecated? A. TKIP B. CCMP C. GCMP D. EAP Which statements describe network characteristics? (Choose three) A. Cost represents the general price of components, installation, and maintenance of the network B. Reliability indicates how protected the network is, including the information that is transmitted over the network C. Topology is a measure of the data rate in bits per second of a given link in the network D. Security depicts the structure of the network E. Scalability indicates how well the network can accommodate more users or data transmission requirements F. Availability is the probability of the network being available for use when required https://www.learncisco.net/courses/icnd-1/building-a-network/the-functions-of-networking.html You are setting up a Cisco IOS router as a DHCP server. Which command is used to identify the IPv4 addresses that will be in the DHCP pool? A. network B. dns-server C. default-router D. ip dhcp excluded-address E. lease F. ip dhcp pool G. domain-name Each virtual OS instance that exists on a server is referred to as a ___________ A. KVM B. VM C. CSR D. hypervisor Which of the following behaviors is applied to a low latency queue in a Cisco router or switch? (Choose two) A. Congestion management B. Shaping C. Policing D. Priority scheduling E. Round robin scheduling Which of the following describes a broadcast type of network communication? A. From one address to a single address B. From one address to all other addresses C. From one address to multiple addresses https://www.learncisco.net/courses/icnd-1/building-a-network/ethernet-protocol.html Which state of the default STP configuration allows ports to listen for BPDUs but not send any? A. Listening B. Learning C. Blocking D. Forwarding How are ACLs processed? A. Entries are processed bottom-up B. Entries are processed top-down C. Entries are processed at the same time D. Entries are processed randomly If you want to be alerted when a device configuration differs from the intended configuration, what should you implement? A. Version control B. Centralized configuration C. Configuration drift D. Configuration monitoring Which of the following are available methods of classifying packets in DiffServ on Cisco routers? (Choose three) A. Matching the IP DSCP field B. Matching the 802.1p CoS field C. Matching fields with an extended IP ACL D. Matching the SNMP Location variable Refer to the exhibit. A technician has installed SwitchB and needs to configure it for remote access from the management workstation connected to SwitchA. Which set of commands is required to accomplish this task? A. SwitchB(config)# interface FastEthernet 0/1 SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0 SwitchB(config-if)# no shutdown B. SwitchB(config)# interface vlan 1 SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0 SwitchB(config-if)# ip default-gateway 192.168.8.254 255.255.255.0 SwitchB(config-if)# no shutdown C. SwitchB(config)# ip default-gateway 192.168.8.254 SwitchB(config)# interface vlan 1 SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0 SwitchB(config-if)# no shutdown D. SwitchB(config)# ip default-network 192.168.8.254 SwitchB(config)# interface vlan 1 SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0 SwitchB(config-if)# no shutdown E. SwitchB(config)# ip route 192.168.8.254 255.255.255.0 SwitchB(config)# interface FastEthernet 0/1 SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0 SwitchB(config-if)# no shutdown Select the link state dynamic routing protocols. (Choose two) A. RIP B. EIGRP C. IS-IS D. OSPF https://www.learncisco.net/courses/icnd-1/ip-routing-technologies/dynamic-routing.html Which issues can be caused by a redundant switch topology? (Choose three) A. MAC address table instability B. Broadcast storms C. Duplicate IP addresses D. Single point of failure E. Multiple frame copies Which RFC defines the private IPv4 address ranges? A. 2784 B. 4443 C. 1985 D. 7868 E. 1918 F. 2328 G. 792 Which VLAN troubleshooting steps are used when there is no connection between PCs? (Choose two) A. Use the [show interfaces switchport] command to see if the native VLAN matches on both sides B. Use the [show interfaces trunk] command to check whether the VLAN is assigned the correct membership C. Use the [show vlan] command to verify that the port is in the correct VLAN D. Use the [show mac address-table] command to check which addresses were learned on a particular port and which VLAN that port is assigned https://www.learncisco.net/courses/icnd-1/medium-size-switched-network-construction/troubleshooting-switched-network.html Imagine you configured OSPFv2 in a small lab network. Which of the following answers list a condition that could keep the routers in your lab from learning all the routes to all the IPv4 routes in your small lab network? (Choose two) A. An ACL could be blocking router advertisements. B. Two neighboring routers that connect to the same link have been configured with the same OSPF area and with the same IPv4 subnet mask. C. Any physical layer problem that would prevent two neighboring routers from being able to ping each others IPv4 addresses in the subnet that exists between the two routers. D. Two neighboring routers that connect to the same link have been configured with the same OSPF process ID on the router ospf command. Which statements describe the benefits of using external authentication for larger networks? (Choose two) A. It requires less administrative effort than local authentication B. It enables the use of Terminal Access Controller Access Control System+, or TACACS+ C. It only allows Secure Shell, or SSH, connections D. It does not require the configuration of a default gateway https://www.learncisco.net/courses/icnd-1/lan-connections/cisco-router-security.html Using the exhibit as a reference, what is a valid key? A. ”lastUpdateTime”: 1572317520439 B. ”CSR1000V” C. ”role” D. ”platformId”: In the virtualization world, the ___________ manages and allocates the host hardware for each VM. A. Host controller B. Hyperthreader C. Hypervisor D. Host service Which of these are QoS requirements when designing a Cisco TelePresence video network? (Choose two) A. One-way delay < 200 ms B. Round-trip delay < 200 ms C. Loss < 5% D. Loss < 0.05% E. Jitter < 100 ms F. Jitter < 50 ms Which of the following is describing the Access mode of Dynamic Trunking Protocol? A. Creates a trunk with the neighboring switch based on the DTP request B. Enables trunking on the interface C. Trunking cannot take place on the port regardless of DTP requests D. Sends a DTP communication that it wants to create a trunk with the neighboring switch E. DTP frames are prevented from being generated from the port https://www.learncisco.net/courses/icnd-2/vlans-and-spanning-tree/dynamic-trunking-protocol.html Which command and mode will successfully configure a hostname of R1 on a Cisco IOS router? A. Router(config)#name R1 B. Router# hostname R1 C. Router(config)#hostname R1 D. Router#name R1 E. Router>hostname R1 F. Router>name R1 Which of the following commands sets the metric in kb/s on a serial interface? A. no shutdown B. interface serial C. show controllers D. clockrate E. bandwidth https://www.learncisco.net/courses/icnd-2/wan-technologies/serial-encapsulation.html Per the command output, with how many routers is router R9 full adjacent over its Gi0/0 interface? A. 7 B. 10 C. 5 D. 2 Refer to the diagram. What method of authentication is being used? A. Open authentication B. CCMP C. WEP D. 802.1x You are setting up remote access on your Cisco IOS switch. What is the purpose of the “login“ command when issued in [line vty] configuration mode? A. It prompts remote users to provide a password B. It allows remote users to connect without a password C. It enables remote login D. It disables remote login E. It grants the login privileged level During a maintenance window, you make some changes to R2. You document these changes in your configuration management system. Later that night, you are called in to fix an issue that requires you to make additional changes to R2. The next morning your co-worker addresses another issue but this time on R1. All of these changes are documented properly but neither you or nor your coworker discuss the changes. These changes stay implemented for months. What is this best described as? A. Version control B. Centralized configuration C. Configuration drift D. Configuration monitoring Of the different public cloud WAN options, which have quality of service capabilities to ensure end-to-end application requirements? (Choose three) A. Internet B. Intercloud exchange C. Ethernet WAN D. MPLS VPN E. Internet VPN With IEEE 802.1x, which role does a LAN switch typically play? A. Authentication server B. Supplicant C. Translator D. Authenticator When comparing next-generation IPS to traditional IPS, what additional capabilities can be leveraged to more efficiently block traffic? (Choose three) A. AVC B. Signature-based filtering C. Contextual awareness D. Event impact level Which information must match between routers to form an OSPF adjacency? (Choose two) A. Authentication B. Router priority C. BDR IP Address D. Stub area flag https://www.learncisco.net/courses/icnd-1/ip-routing-technologies/introducing-ospf.html You are implementing a Router on a Stick Inter-VLAN routing solution. What type of interfaces are needed for this implementation? A. Routed ports B. Switched virtual interfaces C. Virtual template D. Tunnel E. Sub-interfaces What network mask should be used with Class B network to create 40 subnets? A. 255.255.248.0 B. 255.255.255.0 C. 255.255.252.0 D. 255.255.192.0 E. 255.255.254.0 https://www.learncisco.net/courses/icnd-1/lan-connections/network-addressing-scheme.html Review the topology diagram. Network 10.123.0.0/24 is the backbone area. Network 10.12.0.0/24 is area 1, and network 10.34.0.0/29 is in area 2. Which of the following are true? (Choose three) A. R1 is a backbone router. B. R1 is an ABR. C. R1 is an internal router. D. R3 would see the OSPF network of 10.12.0.0/24 as an intra-area route. E. R1 and R3 would have the same LSA information about the backbone area. Which of the following use cases are matching the Fiber Ethernet media type? (Choose two) A. Offers the highest bandwidths compared to the other forms of communication B. A four-pair wire with low cost and low signal degradation C. Acts as a wave guide to transmit light between the two ends https://www.learncisco.net/courses/icnd-1/building-a-network/connecting-to-a-lan.html What is the field that is used on modern systems that allows an IP packet to be marked with a specific QoS value? A. EXP B. CoS C. DSCP D. Traffic Class Which hash method is used by default when using the enable secret Cisco IOS command? A. 3DES B. MD5 C. SHA-0 D. HMAC The show port-security interface f0/1 command lists a port status of Secure-shutdown. Which of the following answer must be true about this interface at this time? A. The show interface status command lists the interface status as connected. B. The show interface status command lists the interface status as err-disabled. C. The show port-security interface command could list a mode of shutdown or restrict, but not protect. D. The show port-security interface command could list a violation counter value of 10. What is the multicast address for hello packets by default on OSPFv3? A. 224.0.0.6 B. FF02::A C. FF02::5 D. 224.0.0.5 When planning a greenfield SDA design, what traditional LAN design points should be included? (Choose two) A. The number of switchports needed in each switch B. The required speed of the switchports C. A security firewall to properly segment traffic D. The Spanning Tree mode of operation to use A switch’s port Gi0/1 has been correctly enabled with port security. The configuration sets the violation mode to restrict. A frame that violates the port security policy enters the interface, followed by a frame that does not. Which of the following answers correctly describe what happens in this scenario? (Choose two) A. The switch puts the interface into an err-disabled state when the first frame arrives. B. The switch generates syslog messages about the violating traffic for the first frame. C. The switch increments the violation counter for Gi0/1 by 1. D. The switch discards both the first and second frame. Identify the commands required to verify both - the IP addresses of a switch and a host. (Choose two) A. show interface status B. show ip interface brief C. ipconfig /renew D. ipconfig /release E. ipconfig /all https://www.learncisco.net/courses/icnd-1/lan-connections/starting-a-router.html Regarding lightweight AP modes, which one of the following is true? A. An AP can operate in multiple modes at the same time. B. An AP only has one possible mode of operation. C. The Run mode is the default mode. D. The SE-Connect mode is used for spectrum analysis. What is the purpose of domain name system (DNS)? A. To map private IPv4 addresses to public IPv4 addresses B. To map MAC addresses to hostnames C. To map IPv4 addresses to hostnames D. To map IPv4 address to NetBIOS names E. To map IPv4 addresses to MAC addresses Given an IP address 172.16.28.252 with a subnet mask of 255.255.240.0, what is the correct network address? A. 172.16.16.0 B. 172.16.0.0 C. 172.16.24.0 D. 172.16.28.0 https://www.learncisco.net/courses/icnd-1/lan-connections/network-addressing-scheme.html Routing tables can be populated in a number of different ways. Which of the following describes the default route type. A. Router attached to this network B. The router interface has a local IP address C. A system administrator manually enters static routes directly into the configuration D. Learned by exchanging routing information E. Used when no explicit route to a destination is found https://www.learncisco.net/courses/icnd-2/troubleshooting-basic-connectivity/identification-of-the-path.html An engineer connects to Router R1 and issues a show ip ospf neighbor command. The status of neighbor 2.2.2.2 lists FULL/BDR. What does the BDR mean? A. R1 is an Area Border Router. B. R1 is a backup designated router. C. Router 2.2.2.2 is an Area Border Router. D. Router 2.2.2.2 is a backup designated router. Which command will take the static default route and inject it in the OSPFv3 database? A. default-route static B. ipv6 router ospf 5 C. default-route ipv6 D. default-information originate How many subnets are created from a Class C addressing space that is using a /29 subnet mask? A. 16 B. 128 C. 64 D. 32 E. 8 F. 4 What guidelines must be followed to successfully form an EtherChannel bundle? (Choose two) A. The same duplex setting must be used B. A mixture of access ports and trunk ports can be used C. Every link that's going to bundled together must be using the exact same speed D. The native VLAN can differ for every port that is being placed into that bundle Of the figures shown, which depicts an accurate Clos Architecture? A. Topology A B. Topology B C. Topology C D. Topology D

Our Recommended Premium CCNA Training Resources

These are the best CCNA training resources online:

Click Here to get the Cisco CCNA Gold Bootcamp, the most comprehensive and highest rated CCNA course online with a 4.8 star rating from over 30,000 public reviews. I recommend this as your primary study source to learn all the topics on the exam.

Want to take your practice tests to the next level? AlphaPrep’s purpose-built Cisco test engine has the largest question bank, adaptive questions, and advanced reporting which tells you exactly when you’re ready to pass the real exam. Click here for your free trial.

The CCNA 200-301 is for the Cisco Certified Network Associate (CCNA) Implementing and Administering Cisco Solutions exam. You can use the practice test to check your knowledge and improve your understanding in preparation for the Cisco CCNA certification exam.

The Cisco CCNA 200-301 practice exam tests include questions to test your knowledge and skills related to Cisco networking fundamentals, which helps you pass the actual exam.

The Cisco CCNA exam objectives include Cisco network fundamentals on routers, switches, IP addresses, etc., network access, IP connectivity such as static and dynamic routing protocol, IP services, network security fundamentals, and automation and programmability.

Cisco CCNA 200-301 Practice Test

Complete this form to get your score report

Our Recommended Premium CCNA Training Resources