Cisco CCNA 200-301 Practice Test

Cisco Practice Tests

Question 1 / 55 - Mode : Exam
Consider the following scenario: Host A has IP address 192.168.6.3 and MAC address 0800:0111:3333. Host B has IP address 192.168.7.3 and MAC address 0800:0222:4444. The router has IP address 192.168.7.1 and MAC address 0800:0444:1111. When Host B receives a packet from Host A, the frame contains the source and destination IP and MAC addresses. What should be the source IP address? A. 0800:0444:1111 B. 192.168.7.3 C. 192.168.6.3 D. 0800:0222:4444 https://www.learncisco.net/courses/icnd-1/lan-connections/packet-delivery-process-at-l3.html Which command is used to enable IPv6 routing? A. ipv6 router B. ipv6 unicast-routing C. enable ipv6 D. ipv6 eigrp Which VLAN troubleshooting steps are used when there is no connection between PCs? (Choose two) A. Use the [show interfaces switchport] command to see if the native VLAN matches on both sides B. Use the [show interfaces trunk] command to check whether the VLAN is assigned the correct membership C. Use the [show vlan] command to verify that the port is in the correct VLAN D. Use the [show mac address-table] command to check which addresses were learned on a particular port and which VLAN that port is assigned https://www.learncisco.net/courses/icnd-1/medium-size-switched-network-construction/troubleshooting-switched-network.html What are the considerations when using Cisco PVST+? (Choose two) A. You can manipulate spanning-tree topologies on a VLAN-by-VLAN basis B. There is only one spanning-tree instance for the entire switched network C. It does not allow load sharing or balancing D. It allows optimal load sharing Four OSPF routers connect to the same LAN. In a new election after all routers have been rebooted, which router wins the DR election? A. R4, router-id 4.4.4.4, priority 1 B. R3, router-id 3.3.3.3, priority 2 C. R1, router-id 1.1.1.1, priority 4 D. R2, router-id 2.2.2.2, priority 3 Which end-to-end connectivity troubleshooting tool will you use to test the IP connectivity between two hosts? A. Ping B. Telnet C. Address Resolution Protocol, or ARP D. Traceroute https://www.learncisco.net/courses/icnd-2/troubleshooting-basic-connectivity/troubleshooting-connectivity.html What command is used to verify MAC address table entries? A. show mac address-table B. show mac-address C. show mac-address table D. show address table Of the different public cloud WAN options, which have quality of service capabilities to ensure end-to-end application requirements? (Choose three) A. Internet B. Intercloud exchange C. Ethernet WAN D. MPLS VPN E. Internet VPN Which statements accurately describe a network? (Choose three) A. A network is a collection of connected devices that have the ability to communicate with each other B. Networks are capable of transmitting data in many kinds of environments, such as homes, small businesses, and large enterprises C. A main office can have hundreds or even thousands of people who depend on network access to do their jobs D. A main office usually has one large network to connect users E. Remote locations cannot connect to a main office through a network F. The purpose of a network is to allow workers access to all information and components that are accessible by the network https://www.learncisco.net/courses/icnd-1/building-a-network/the-functions-of-networking.html What protocol is used to synchronize time between various Cisco IOS devices in your network? A. LACP B. NTP C. DTP D. VTP E. CDP F. STP G. PAgP Which three of these statements regarding 802.1Q trunking are correct? (Choose three) A. 802.1Q native VLAN frames are untagged by default. B. 802.1Q trunking ports can also be secure ports. C. 802.1Q trunks can use 10 Mb/s Ethernet interfaces. D. 802.1Q trunks require full-duplex, point-to-point connectivity. E. 802.1Q trunks should have native VLANs that are the same at both ends. https://www.learncisco.net/courses/icnd-1/medium-size-switched-network-construction/vlans-and-trunk.html You are performing password recovery on your Cisco 2900 ISR. You are currently in ROMMON mode. What do you need to change the configuration register value to in order to perform password recover? A. 0x2142 B. 0x2102 C. 0x2100 D. 0x2140 Which option is not one of the most commonly deployed virtualization vendors and products? A. Oracle XenSpace B. Microsoft Hyper-V C. VMware vCenter D. Red Hat KVM Which of the following describes a dynamic NAT configuration? A. Manually configured, one-to-one address mapping B. Automatically assigned from an address pool, many-to-many address mapping C. Many-to-one address mapping https://www.learncisco.net/courses/icnd-1/acls-and-nat/address-translation.html Of the figures shown, which depicts an accurate Clos Architecture? A. Topology A B. Topology B C. Topology C D. Topology D Which layer of the OSI model provides connectivity and path selection between two host systems? A. Session B. Network C. Transport D. Application E. Data-link F. Presentation https://www.learncisco.net/courses/icnd-1/building-a-network/host-to-host-communications.html Devices using a wireless LAN must operate in which one of the following modes? A. Round-robin access B. Half duplex C. Full duplex D. None of these answers Using the exhibit as a reference, how many JSON objects are there? A. 11 B. 1 C. 2 D. 12 Review the topology. All subnets exist in OSPF area 0. Which command, if issued on R3, would show all the LSAs known by R3? A. Show running-config B. Show ip ospf interface C. Show ip ospf neighbors D. Show ip route ospf E. Show ip ospf database Regarding lightweight AP modes, which one of the following is true? A. An AP can operate in multiple modes at the same time. B. An AP only has one possible mode of operation. C. The Run mode is the default mode. D. The SE-Connect mode is used for spectrum analysis. What is the first 24 bits in a MAC address called? A. NIC B. BIA C. OUI D. VAI https://www.learncisco.net/courses/icnd-1/building-a-network/ethernet-protocol.html Which two of these statements are true of IPv6 address representation? (Choose two) A. There are four types of IPv6 addresses: unicast, multicast, anycast, and broadcast. B. A single interface may be assigned multiple IPv6 addresses of any type. C. Every IPv6 interface contains at least one loopback address. D. The first 64 bits represent the dynamically created interface ID. E. Leading zeros in an IPv6 16 bit hexadecimal field are mandatory. https://www.learncisco.net/courses/icnd-1/introducing-ipv6/ipv6-address-types.html Refer to the exhibit. The network administrator normally establishes a Telnet session with the switch from host A. However, host A is unavailable. The administrator's attempt to telnet to the switch from host B fails, but pings to the other two hosts are successful. What is the issue? A. Host B and the switch need to be in the same subnet. B. The switch interface connected to the router is down. C. Host B needs to be assigned an IP address in VLAN 1. D. The switch needs an appropriate default gateway assigned. E. The switch interfaces need the appropriate IP addresses assigned. What are three advantages of VLANs? (Choose three) A. VLANs establish broadcast domains in switched networks. B. VLANs utilize packet filtering to enhance network security. C. VLANs provide a method of conserving IP addresses in large networks. D. VLANs provide a low-latency internetworking alternative to routed networks. E. VLANs allow access to network services based on department, not physical location. F. VLANs can greatly simplify adding, moving, or changing hosts on the network. https://www.learncisco.net/courses/ccna/part-5-virtual-lans-vlans/vlans-review.html An interface on your Catalyst switch is configured with BPDU Guard. The interface has received numerous BPDUs and is now listed as being down/down. You plan on eliminating the reason why the BPDUs were received on the port. In addition, you want the port to automatically recover from the down/down state after 30 seconds. Which feature can you enable to ensure that the port automatically recovers? A. IPSLA B. Root guard C. Loop guard D. UDLD E. Errdisable recovery Which public cloud WAN connection options do not offer the ability to have reliable QoS? (Choose two) A. Internet B. Internet VPN C. MPLS VPN D. Ethernet VPN E. Intercloud What are the functions of the standby router when there is L3 redundancy? (Choose two) A. Sends out hello messages B. Knows the IP address of the virtual router C. Active forwarding of packets for the virtual router is assumed D. Default gateway ARP requests are responded to with the virtual router MAC E. Listens for periodic hello messages F. If the other router is not heard from, it assumes active forwarding of packets https://www.learncisco.net/courses/icnd-2/etherchannel-and-l3-redundancy/gateway-redundancy.html What is known as “one-to-nearest“ addressing in IPv6? A. global unicast B. anycast C. multicast D. unspecified address https://www.learncisco.net/courses/icnd-1/introducing-ipv6/ipv6-address-types.html R1, R2, R3, and R4 have their Fast Ethernet 0/0 interfaces attached to the same VLAN. A network engineer has typed a configuration for each router by using a word processor. He will later copy and paste the configuration into the routers. Examine the following exhibit, which lists configuration for the four routers, as typed by the network engineer. Assuming that all four routers can ping each other’s LAN IP addresses after the configuration has been applied, choose the routers that will be able to form a neighbor relationship with the other routers on the LAN. (You can assume that, if not shown in the exhibit, all other related parameters are still set to their defaults.) (Choose two) A. R1 B. R2 C. R3 D. R4 E. None of the routers will exchange routing information. Using the exhibit as a reference, what is a valid key? A. ”lastUpdateTime”: 1572317520439 B. ”CSR1000V” C. ”role” D. ”platformId”: Which of the following are required attributes of a REST-based API? (Choose two) A. Uses HTTP B. Objects noted as to whether they can be cached C. Classful operation D. Client/server architecture Which IPv6 command allows you to verify general parameters such as the reference bandwidth? A. show ipv6 ospf interface brief B. show ipv6 ospf C. show ipv6 route summarization D. show ipv6 protocols Which hash method is used by default when using the enable secret Cisco IOS command? A. 3DES B. MD5 C. SHA-0 D. HMAC Some IOS commands store passwords as clear text, but you can then encrypt the passwords with the service password-encryption global command. By comparison, other commands store a computed hash of the password, rather than storing the password. Comparing the two options, which one answer is the most accurate about why one method is better than the other? A. Using hashes is preferred because encrypted IOS passwords can be easily decrypted. B. Using hashes is preferred because of the large CPU effort required for encryption. C. Using encryption is preferred because it provides stronger password protection. D. Using encryption is preferred because of the large CPU effort required for hashes. What is the purpose of the “service password-encryption“ command? A. It encrypts all passwords on your router. B. It encrypts the line console password only. C. It encrypts the vty password only. D. It is not a valid cisco command Which of the following commands would you use to enable EIGRP only on those interfaces with an IP address from 10.1.1.0 through 10.1.1.63? A. network 10.1.1.0 0.0.0.63 B. network 10.1.1.0/63 C. router eigrp 10.1.1.0 0.0.0.63 D. network 10.0.0.0 0.0.0.255 Review the topology diagram. Network 10.123.0.0/24 is the backbone area. Network 10.12.0.0/24 is area 1, and network 10.34.0.0/29 is in area 2. Which of the following are true? (Choose three) A. R1 is a backbone router. B. R1 is an ABR. C. R1 is an internal router. D. R3 would see the OSPF network of 10.12.0.0/24 as an intra-area route. E. R1 and R3 would have the same LSA information about the backbone area. Which command stores passwords as an SHA-256 or MD5 hash? A. service password-encryption B. service password-encryption {sha256 \| md5} C. enable password {sha256 \| md5} D. enable hash-password E. None of the above. Review the following router configuration and identify the correct statements regarding telnet access to the router: Router(config)#access-list 1 deny host 10.1.20.1 Router(config)#access-list 1 deny host 10.1.20.2 Router(config)#access-list 1 permit host 10.1.10.1 Router(config)#access-list 1 permit host 10.1.10.2 Router(config)#access-list 1 permit 10.1.20.0 0.0.0.255 Router(config)#line vty 0 4 Router(config-line)#access-class 1 in (Choose two) A. Telnet access from all hosts in the 10.1.20.0/24 network is denied except 10.1.20.1 and 10.1.20.2 B. Telnet access from hosts 10.1.20.1 and 10.1.20.2 is allowed C. Telnet access from hosts 10.1.10.1 and 10.1.10.2 is allowed D. Telnet access from all hosts in the 10.1.10.0/24 network is allowed E. Telnet access from all hosts in the 10.1.20.0/24 network is allowed except 10.1.20.1 and 10.1.20.2 F. Telnet attempts that are denied will generate a syslog message Which of these are QoS requirements when designing a Cisco voice network? (Choose two) A. Jitter < 30 ms B. Loss < 1% C. One-way delay < 200 ms D. Jitter < 50 ms E. Loss < 2% F. Round-trip delay < 200 ms Which two of these statements regarding RSTP are correct? (Choose two) A. RSTP cannot operate with PVST+. B. RSTP defines new port roles. C. RSTP defines no new port states. D. RSTP is a proprietary implementation of IEEE 802.1D STP. E. RSTP is compatible with the original IEEE 802.1D STP. https://www.learncisco.net/courses/icnd-2/vlans-and-spanning-tree/stp-protocol-types.html What is the first thing a Cisco router does as part of its initial startup? A. Finds and loads the configuration file B. Performs software initialization C. Runs the power-on self test, or POST, to test the hardware D. Finds and loads the Cisco Internetwork Operating System, or 10S, image https://www.learncisco.net/courses/icnd-1/lan-connections/starting-a-router.html An enterprise plans to start using a public cloud service and is considering different WAN options. The answers list four options under consideration. Which one option has the most issues if the company chooses one cloud provider but then later wants to change to use a different cloud provider instead? A. Using private WAN connections directly to the cloud provider B. Using an Internet connection without VPN C. Using an intercloud exchange D. Using an Internet connection with VPN Consider the following scenario: Host A has IP address 192.168.6.3 and MAC address 0800:0111:3333. Host B has IP address 192.168.7.3 and MAC address 0800:0222:4444. The router has IP address 192.168.7.1 and MAC address 0800:0444:1111. When Host B receives a packet from Host A, the frame contains the source and destination IP and MAC addresses. What should be the destination IP address? A. 0800:0444:1111 B. 192.168.7.3 C. 192.168.6.3 D. 0800:0222:4444 https://www.learncisco.net/courses/icnd-1/lan-connections/packet-delivery-process-at-l3.html You are implementing a VLSM network. You are using the Class B network of 172.16.0.0/16 and need to create 256 networks from this. The fifth network will then be subnetted into /30 networks. What is the subnet ID of the fourth /30 network? A. 172.16.4.12/30 B. 172.16.4.4/30 C. 172.16.4.6/30 D. 172.16.4.8/30 E. 172.16.4.14/30 F. 172.16.4.10/30 Which of the following controllers (if any) from Cisco uses a mostly centralized control plane model? A. Cisco Open SDN Controller B. Cisco Application Policy Infrastructure Controller (APIC) C. Cisco APIC Enterprise Module (APIC-EM) D. None of these controllers uses a mostly centralized control plane. Which of the following dynamic routing protocols are Distance Vector routing protocols? (Choose two) A. IS-IS B. EIGRP C. OSPF D. BGP E. RIP In what security zone are the public web servers located? A. DMZ B. Inside C. Outside D. Campus Which application(s) would Jitter and Delay not be a concern for the users experience? A. Online Gaming. B. VoIP. C. Web browsers. D. videoconferencing. What is the result of issuing the command “no service password-encryption“ on a Cisco IOS router? A. All future passwords will be stored as plain text in the running configuration B. All current encrypted passwords and future passwords will be encrypted in the running configuration C. All current encrypted passwords and future passwords will be stored as plain text in the running configuration D. All future passwords will be encrypted in the running configuration Which options are not one of the manageable QoS characteristics of network traffic? (Choose two) A. Delay B. Jitter C. Queue size D. Clock rate E. Bandwidth F. Loss What is the benefit of using a leased line between two offices for connectivity? A. Reduced Delay and Jitter B. Reduced Cost C. Intranet Reduction in Traffic D. Internet Control Which IPv6 address is the equivalent of the IPv4 interface loopback address 127.0.0.1? A. ::1 B. :: C. 2000::/3 D. 0::/10 https://www.learncisco.net/courses/icnd-2/troubleshooting-basic-connectivity/ipv6-unicast-addresses.html Refer to the diagram. What method of authentication is being used? A. Open authentication B. CCMP C. WEP D. 802.1x To connect a Cisco wireless LAN controller to a wired network, which of the following would you use? Assume that this connection will carry traffic to and from APs. A. Console port B. Service port C. Distribution system port D. AP data port

Our Recommended Premium CCNA Training Resources

These are the best CCNA training resources online:

Click Here to get the Cisco CCNA Gold Bootcamp, the most comprehensive and highest rated CCNA course online with a 4.8 star rating from over 30,000 public reviews. I recommend this as your primary study source to learn all the topics on the exam.

Want to take your practice tests to the next level? AlphaPrep’s purpose-built Cisco test engine has the largest question bank, adaptive questions, and advanced reporting which tells you exactly when you’re ready to pass the real exam. Click here for your free trial.

The CCNA 200-301 is for the Cisco Certified Network Associate (CCNA) Implementing and Administering Cisco Solutions exam. You can use the practice test to check your knowledge and improve your understanding in preparation for the Cisco CCNA certification exam.

The Cisco CCNA 200-301 practice exam tests include questions to test your knowledge and skills related to Cisco networking fundamentals, which helps you pass the actual exam.

The Cisco CCNA exam objectives include Cisco network fundamentals on routers, switches, IP addresses, etc., network access, IP connectivity such as static and dynamic routing protocol, IP services, network security fundamentals, and automation and programmability.

Cisco CCNA 200-301 Practice Test

Complete this form to get your score report

Our Recommended Premium CCNA Training Resources