Cisco CCNA 200-301 Practice Test

Cisco Practice Tests

Question 1 / 55 - Mode : Exam
Identify the statements that describe the role of ARP. (Choose two) A. It records recent bindings of IP address to Medium Access Control, or MAC, addresses B. It resolves known IP addresses to MAC addresses C. It uses a signaling protocol when sharing MAC addresses D. It finds IP addresses in DNS https://www.learncisco.net/courses/icnd-1/lan-connections/packet-delivery-process-at-l3.html Some IOS commands store passwords as clear text, but you can then encrypt the passwords with the service password-encryption global command. By comparison, other commands store a computed hash of the password, rather than storing the password. Comparing the two options, which one answer is the most accurate about why one method is better than the other? A. Using hashes is preferred because encrypted IOS passwords can be easily decrypted. B. Using hashes is preferred because of the large CPU effort required for encryption. C. Using encryption is preferred because it provides stronger password protection. D. Using encryption is preferred because of the large CPU effort required for hashes. The type of service field in an IPv4 header is used for QoS. Which field in the IPv6 header is used for QoS? A. Traffic class B. Flow label C. Next header D. Source address E. Hop limit F. Destination address Which of the following describes the STP protocol? A. Assumes one 802.1D spanning tree for the entire bridged network B. Provides a separate 802.1D spanning tree for each virtual LAN, or VLAN, configured C. Provides fast conversion with a single instance of STP D. Provides fast conversion with an instance of spanning tree per VLAN https://www.learncisco.net/courses/icnd-2/vlans-and-spanning-tree/stp-protocol-types.html Four OSPF routers connect to the same LAN. In a new election after all routers have been rebooted, which router wins the DR election? A. R4, router-id 4.4.4.4, priority 1 B. R3, router-id 3.3.3.3, priority 2 C. R1, router-id 1.1.1.1, priority 4 D. R2, router-id 2.2.2.2, priority 3 If a /20 subnet was applied to a Class B address, how many subnets would you create? A. 8 B. 32 C. 16 D. 4 E. 14 https://www.learncisco.net/courses/icnd-1/lan-connections/network-addressing-scheme.html Which of the following commands globally enables PortFast on all nontrunking ports? A. spanning-tree portfast default B. spanning-tree portfast C. spanning-tree bpduguard enable D. spanning-tree portfast bpduguard default https://www.learncisco.net/courses/icnd-1/medium-size-switched-network-construction/performance-with-spanning-tree.html Which command can be used to verify that the current IPv6 path matches the desired route to the server? A. show ipv6 cef B. show ipv6 mroute C. show ipv6 neighbors D. show ipv6 route What is the name of the firewall feature that, when used, can maintain a historical database of each connection through a device: Where it was sourced, destined, and which protocol and protocol port it was using? A. Stateless Inspection B. Stateful Inspection C. Network Protocol Analysis D. Protocol State Analysis Refer to the exhibit. Which statement is true? A. The Fa0/11 role confirms that SwitchA is the root bridge for VLAN 20. B. VLAN 20 is running the Per VLAN Spanning Tree Protocol. C. The MAC address of the root bridge is 0017.596d.1580. D. SwitchA is not the root bridge, because not all of the interface roles are designated. You are given an address scheme of 172.16.10.0/21. Which VLSM will create room for 20 hosts and reduce the amount of unused address space? A. 172.16.10.0/27 B. 172.16.10.0/26 C. 172.16.10.0/28 D. 172.16.10.0/24 https://www.learncisco.net/courses/ccna/part-2-ip-addressing-and-subnetting-nat/variable-length-subnet-mask.html You are creating a number IPv4 extended ACL. What is the valid number range you can use? A. 1100-1199 B. 100-199 C. 200-299 D. 1-99 E. 700-799 If you want to be alerted when a device configuration differs from the intended configuration, what should you implement? A. Version control B. Centralized configuration C. Configuration drift D. Configuration monitoring Which of the following four TCP/IP layers determines the best path through the network? A. Network Access B. Transport C. Internet D. Application https://www.learncisco.net/courses/icnd-1/building-a-network/host-to-host-communications.html From the following options, what are the required REST API attributes? (Choose two) A. JSON-formatted data B. Unlayered systems C. Layered systems D. Client-server architecture Which of the following behaviors is applied to a low latency queue in a Cisco router or switch? (Choose two) A. Congestion management B. Shaping C. Policing D. Priority scheduling E. Round robin scheduling You have taken the network 10.0.0.0 255.0.0.0 and created multiple subnets with a 255.255.255.128 subnet mask. What is the block size of each of these new subnets? A. 32 B. 256 C. 512 D. 16 E. 128 F. 64 Which of the following best describes a virtual network function in a public cloud service? A. A subset of a physical networking device, configured by the cloud provider and allocated for use by that customer only B. A networking function implemented by the cloud provider for the customer, but with no direct customer access to the server that provides the service C. A networking function implemented by the cloud provider for the customer as a VM that is directly accessible and configurable by the customer D. Any networking feature implemented on a VM in a cloud service With IEEE 802.1x, which role does a LAN switch typically play? A. Authentication server B. Supplicant C. Translator D. Authenticator Which command will assign a global IPv6 address with an autoconfigured interface portion to a router interface? A. ipv6 address 2001:db8:1:1::0001/64 eui-64 B. ipv6 address 2001:db8:1:1::0001/64 auto-configure C. ipv6 address 2001:db8:1:1::/64 auto-configure D. ipv6 address 2001:db8:1:1::/64 eui-64 E. ipv6 address 2001:db8:1:1::/64 Which of the following describes the Rapid PVST+ protocol? A. Assumes one 802.1D spanning tree for the entire bridged network B. Provides a separate 802.1D spanning tree for each virtual LAN, or VLAN, configured C. Provides fast conversion with a single instance of STP D. Provides fast conversion with an instance of spanning tree per VLAN https://www.learncisco.net/courses/icnd-2/vlans-and-spanning-tree/stp-protocol-types.html __________ means that the QoS tool changes one or more header fields, setting a value in the header. A. Marking B. Classifying C. Insertion D. Qualifying You need to prevent your router from receiving and processing RIPv2 routing updates. How can you accomplish this? A. Create an ACL denying TCP port 520 packets and apply it outbound on the interface B. Create an ACL denying UDP port 520 packets and apply it inbound on the interface C. Create an ACL denying TCP port 520 packets and apply it inbound on the interface D. Create an ACL denying UDP port 520 packets and apply it outbound on the interface E. Enable the passive interface feature on the interface What type of variable is being shown? Routers = [R1,R2,R3] A. List B. Dictionary C. Simple D. Unsigned integers enable secret [password] is hashed using the _______ algorithm. A. MD5 B. AH C. PSK D. ESP E. WPA2 Which of the following attributes do QoS tools manage? (Choose three) A. Bandwidth B. Delay C. Load D. MTU E. Loss Identify the commands used to correctly configure multiarea OSPF. (Choose two) A. OSPF can be enabled universally within an area by using the [ip ospf area] command on any router within a specific area. B. The [ip ospf cost] command specifies the OSPF cost of sending a packet on an interface. C. The [network area] command defines the interfaces on which OSPF runs and defines the area IDs for those interfaces. D. Individual routers can only be configured with a single OSFP routing process number using the [router ospf] command. https://www.learncisco.net/courses/icnd-2/implementing-a-multiarea-ospf-solution/multiarea-ospf-configuration.html A Cisco Catalyst switch connects to what should be individual user PCs. Each port has the same port security configuration, configured as follows: interface range gigabitethernet 0/1 - 24 switchport mode access switchport port-security switchport port-security mac-address sticky Which of the following answers describe the result of the port security configuration created with these commands? (Choose two) A. Prevents unknown devices with unknown MAC addresses from sending data through the switch ports. B. If a user connects a switch to the cable, prevents multiple devices from sending data through the port. C. Will allow any one device to connect to each port, and will save that device’s MAC address into the startup-config D. Will allow any one device to connect to each port, but will not save that device’s MAC address into the startup-config What are the key characteristics of OSPFv3? (Choose two) A. The OSPFv3 metric is based on interface costing B. OSPFv3 omits the use of multiarea network designs with area border routers, or ABRs, that segment the network C. Link-state advertisements, or LSAs, are not flooded throughout an OSPF domain D. IPv6 uses OSPFv3 rather than OSPFv2 https://www.learncisco.net/courses/icnd-2/implementing-a-multiarea-ospf-solution/ospfv3-configuration.html Which of the following OSPF packet types requests missing information? A. link-state acknowledgement, or LSAck B. link-state update, or LSU C. link-state request, or LSR D. database description package, or DBD https://www.learncisco.net/courses/icnd-2/an-overview-of-ospf/link-state-databases.html You are upgrading your Cisco IOS image on your 2900 ISR. You won't be removing the old IOS image from the device for disaster recovery reasons. After copying the IOS image from the tftp server to flash and rebooting the device, you notice that the old operating system image is still loading. How can you load the new IOS image? A. Issue the boot system command and reload the device B. Issue the config-register 0x2142 command and reload the device C. Issue the copy running-config startup-config command D. Issue the write memory command To connect a Cisco wireless LAN controller to a wired network, which of the following would you use? Assume that this connection will carry traffic to and from APs. A. Console port B. Service port C. Distribution system port D. AP data port Of the different public cloud WAN options, which have quality of service capabilities to ensure end-to-end application requirements? (Choose three) A. Internet B. Intercloud exchange C. Ethernet WAN D. MPLS VPN E. Internet VPN An engineer connects to Router R1 and issues a show ip ospf neighbor command. The status of neighbor 2.2.2.2 lists FULL/BDR. What does the BDR mean? A. R1 is an Area Border Router. B. R1 is a backup designated router. C. Router 2.2.2.2 is an Area Border Router. D. Router 2.2.2.2 is a backup designated router. Which of the following controllers (if any) from Cisco uses a mostly centralized control plane model? A. Cisco Open SDN Controller B. Cisco Application Policy Infrastructure Controller (APIC) C. Cisco APIC Enterprise Module (APIC-EM) D. None of these controllers uses a mostly centralized control plane. Which protocol number represents ICMPv6? A. 89 B. 88 C. 17 D. 1 E. 58 F. 6 When are VTP messages sent to clients for synchronization while using a VTP server? (Choose two) A. Every five minutes by default B. Every ten minutes by default C. Only when manually triggered D. Any time there is a change Which of the following cloud services is most likely to be used for software development? A. IaaS B. PaaS C. SaaS D. SLBaaS What is the field that is used on modern systems that allows an IP packet to be marked with a specific QoS value? A. EXP B. CoS C. DSCP D. Traffic Class What is the best method of ensuring that your preferred switch is the root bridge? A. Allow the devices to always elect the best path without any special configuration B. Manually set the priority of each switch in your topology C. Manually set the IP configuration of the switches to modify the priority of each switch D. Use the default configuration and built-in macros You are working in a data center environment and are assigned the address range 10.188.31.0/23. You are asked to develop an IP addressing plan to allow the maximum number of subnets with as many as 30 hosts each. Which IP address range meets these requirements? A. 10.188.31.0/26 B. 10.188.31.0/25 C. 10.188.31.0/28 D. 10.188.31.0/27 E. 10.188.31.0/29 https://www.learncisco.net/courses/ccna/part-2-ip-addressing-and-subnetting-nat/variable-length-subnet-mask.html You want to change the VLAN for FastEthernet 0/2. Which command should you use to do so? A. switchport access B. name C. vlan id D. vlan name E. show vlan brief https://www.learncisco.net/courses/icnd-1/medium-size-switched-network-construction/vlans-and-trunk.html Identify the information that must match between routers in order to form an OSPF adjacency. (Choose two) A. Area ID B. Router ID C. Neighbors D. Hello and dead intervals https://www.learncisco.net/courses/icnd-1/ip-routing-technologies/introducing-ospf.html What commands would you need to configure to enable DHCP Snooping so that PC4 couldn’t become a rogue DHCP server? A. Configure the following on SW 2: ip dhcp snooping, ip dhcp snooping vlan 10, int gi0/12, ip dhcp snooping trust B. Configure the following on SW 1: ip dhcp snooping, ip dhcp snooping vlan 10, int gi0/24, ip dhcp snooping trust C. Configure the following on SW 2: ip dhcp snooping, ip dhcp snooping vlan 10, int gi0/24, ip dhcp snooping trust D. Configure the following on SW 2: ip dhcp snooping, ip dhcp snooping vlan 20, int gi0/24, ip dhcp snooping trust E. Configure the following on SW 2: ip dhcp snooping, ip dhcp snooping vlan 20, int gi0/12, ip dhcp snooping trust F. Configure the following on SW 1: ip dhcp snooping, ip dhcp snooping vlan 20, int gi0/24, ip dhcp snooping trust What is the name of the protocol that is used by IEEE 802.1x devices to communicate with the authenticator and authentication server? A. EAP B. EAPoL C. RADIUS D. TACACS+ What would the following access list entry accomplish when configuring your router? permit tcp host 192.0.0.130 host 192.0.0.227 eq 80 (Choose two) A. Without any other statements, all other hosts would be denied access to 192.0.0.277 B. It permits traffic from 192.0.0.130 to access 192.0.0.277 using anything but HTTP C. It permits traffic from 192.0.0.130 to access 192.0.0.277 using FTP D. It permits traffic from 192.0.0.130 to access 192.0.0.277 using HTTP If you take the network 192.168.1.0/24 and create four subnets from it, what are the new subnet IDs? (Choose four) A. 192.168.1.128 B. 192.168.1.32 C. 192.168.1.96 D. 192.168.1.64 E. 192.168.1.192 F. 192.168.1.0 Which layer of the OSI model ensures data traffic reliability and the breaking down of large files into smaller segments? A. Session B. Network C. Transport D. Application E. Data-link F. Presentation https://www.learncisco.net/courses/icnd-1/building-a-network/host-to-host-communications.html Identify the commands required to verify both - the IP addresses of a switch and a host. (Choose two) A. show interface status B. show ip interface brief C. ipconfig /renew D. ipconfig /release E. ipconfig /all https://www.learncisco.net/courses/icnd-1/lan-connections/starting-a-router.html Suppose two APs are located near each other. Which channel use strategy will result in nonoverlapping channels for Wi-Fi use? (Choose two) A. Use 2.4-GHz channel 1 on AP-A and channel 2 on AP-B. B. Use 2.4-GHz channel 1 on AP-A and 5-GHz channel 48 on AP-B. C. Use 5-GHz channel 36 on AP-A and channel 40 on AP-B. D. Use 5-GHz channel 36 on AP-A and channel 37 on AP-B. A large number of CRC errors may indicate the presence of electromagnetic interference. What command is used to troubleshoot CRC errors? A. show controller B. show shutdown C. show interface D. show counters E. show memory https://www.learncisco.net/courses/icnd-1/ethernet-lans/troubleshooting-switch-issues.html Which of the following are required attributes of a REST-based API? (Choose two) A. Uses HTTP B. Objects noted as to whether they can be cached C. Classful operation D. Client/server architecture Imagine you configured OSPFv2 in a small lab network. Which of the following answers list a condition that could keep the routers in your lab from learning all the routes to all the IPv4 routes in your small lab network? (Choose two) A. An ACL could be blocking router advertisements. B. Two neighboring routers that connect to the same link have been configured with the same OSPF area and with the same IPv4 subnet mask. C. Any physical layer problem that would prevent two neighboring routers from being able to ping each others IPv4 addresses in the subnet that exists between the two routers. D. Two neighboring routers that connect to the same link have been configured with the same OSPF process ID on the router ospf command. Per the command output, with how many routers is router R9 full adjacent over its Gi0/0 interface? A. 7 B. 10 C. 5 D. 2 You are configuring port security on a Catalyst IOS switch. You need to choose a violation mode that will deny frames that are in violation of the port security settings while still allowing frames that are not in violation. In addition, syslog messages need to be generated and the port security violation counter must increase each time a violation occurs. Which port security violation mode should you choose? A. Err-disable B. Protect C. Shutdown D. Disable E. Restrict

Our Recommended Premium CCNA Training Resources

These are the best CCNA training resources online:

Click Here to get the Cisco CCNA Gold Bootcamp, the most comprehensive and highest rated CCNA course online with a 4.8 star rating from over 30,000 public reviews. I recommend this as your primary study source to learn all the topics on the exam.

Want to take your practice tests to the next level? AlphaPrep’s purpose-built Cisco test engine has the largest question bank, adaptive questions, and advanced reporting which tells you exactly when you’re ready to pass the real exam. Click here for your free trial.

The CCNA 200-301 is for the Cisco Certified Network Associate (CCNA) Implementing and Administering Cisco Solutions exam. You can use the practice test to check your knowledge and improve your understanding in preparation for the Cisco CCNA certification exam.

The Cisco CCNA 200-301 practice exam tests include questions to test your knowledge and skills related to Cisco networking fundamentals, which helps you pass the actual exam.

The Cisco CCNA exam objectives include Cisco network fundamentals on routers, switches, IP addresses, etc., network access, IP connectivity such as static and dynamic routing protocol, IP services, network security fundamentals, and automation and programmability.

Cisco CCNA 200-301 Practice Test

Complete this form to get your score report

Our Recommended Premium CCNA Training Resources